fr 5 01 thru fr 5 07 5 amp fast recovery rectifier 50 to 1000 volts features low cost low leakage low forward voltage drop high current capability fast switching speed for high efficiency maximum ratings operating temperature: - 5 5 c to +15 0 c storage temperature: - 5 5 c to +15 0 c catalog number device marking maximum re current peak reverse voltage maximum rms voltage maximum dc blocking voltage fr 5 01 --- 50v 35v 50v fr 5 02 --- 100v 70v 100v fr 5 03 --- 200v 1 40v 200v fr 5 04 --- 400v 280v 400v fr 5 05 --- 600v 420v 600v fr 5 06 --- 800v 560v 800v fr 5 07 --- 1000v 700v 1000v electrical characteristics @ 25 c unless otherwise specified average forward current i f(av) 5 a t a = 5 5 c peak forward surge current i fsm 20 0 a 8.3ms, half sine maximum instantaneous forward voltage v f 1.3 5 v i fm = 5 .0a; t a = 25 c maximum dc reverse current at rated dc blocking voltage i r 10 m a 150 m a t a = 25 c t a = 55 c maximum reverse recovery time fr 5 01- 5 04 fr 5 05 fr 5 06- 5 07 t rr 150ns 250ns 500ns i f =0.5a, i r =1.0a, i rr =0.25a typical junction capacitance c j 65pf measured at 1.0mhz, v r =4.0v *pulse test: pulse width 300 m sec, duty cycle 1% do-201ad dimensions inches mm dim min max min max note a --- .370 --- 9.50 b --- .250 --- 6.40 c .048 .052 1.20 1.30 d 1.000 --- 25.40 --- a b c d d cathode mark ww w . cn ele ct r .com shanghai lunsure electronic technology co.,ltd tel:0086-21-37185008 fax:0086-21-57152769
fr 5 01 thru fr 5 07 average forward rectified current - amperes versus ambient temperature - c figure 2 forward derating curve 0 17550 75 100 125 0 1. 0 2 .0 3. 0 single phase, half wave 60hz resistive or inductive load amps c 150 4. 0 5.0 6. 0 junction capacitance - pf versus reverse voltage - volts instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics 4 6 20 10 amps .4 .6 .8 1.0 12 1.4 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c volts figure 3 junction capacitance .1 .2 1 .4 2 10 20 404 100 200 1 2 6 10 20 100 pf volts 60 40 4 400 1000 t j =25 c ww w . cn el ec tr .com
fr 5 01 thru fr 5 07 t rr +0.5a 0 -0.25 -1.0 1cm set time base for 20/100ns/cm 25vdc 1 w 50 w 10 w oscilloscope note 1 pulse generator note 2 notes: 1. rise time = 7ns max. input impedance = 1 megohm, 22pf 2. rise time = 10ns max. source impedance = 50 ohms 3. resistors are non-inductive figure 5 reverse recovery time characteristic and test circuit diagram 1 100 4 0 50 100 150 8 figure 4 peak forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 200 250 300 ww w . cn ele ct r .com
|